







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Orinda, CA: What the Job Actually Involves
Door installation in Orinda, CA typically runs $650 – $2,400 per opening for a standard exterior or interior door, and $2,800 – $6,500 when you’re hanging a heavy custom slab, a wide slider, or a door that has to be reframed into hillside-era construction. Most single-door jobs wrap in one day; a full exterior swap with trim, flashing, and paint lands at two to three. Call (833) 700-4611 for a free on-site estimate and a written, line-item number before any work starts.

The Five Stages We Work Through on Every Orinda Door Install

Nobody wants a door hung twice. Here’s the sequence we run, and where you make the calls.
Stage 1: Measure, swing, and sight lines (day 1, about an hour)
We measure the rough opening in three places, check the frame for plumb and square, and confirm the swing direction, hinge side, and whether the door needs to sit flush with interior drywall or proud of it. This is where you pick handedness and decide if the existing casing stays or comes off. On Orinda hillside homes, this is also where we note whether the wall has shifted since the 1960s, because a square door in an out-of-square opening means planing, shimming, or a custom frame.
Stage 2: Demo and prep the opening (2 – 4 hours)
We pull the old door, slab, and casing, then inspect the rough framing and the header. Rotted sill plates and water-stained subfloor show up more than you’d expect on north-facing Orinda entries where the fog sits. Any soft wood gets cut out and replaced before a new door goes back in. You don’t have to decide anything here unless we find framing rot, which we photograph and price before touching.
Stage 3: Set and shim the unit (2 – 3 hours)
The new door goes in plumb and level, shimmed at the hinges and the lock side so the slab neither drags nor springs open. We check the reveal gap is even all the way around and the door closes with a two-finger push. For exterior doors we dry-fit before fastening, because once the flashing is set you want the reveal right the first time.
Stage 4: Weatherproof and seal (2 – 3 hours)
Exterior doors get a door pan or sill pan, flashing tape at the head and jambs, and a bead of sealant under the threshold and behind the brick mold. This is the stage that decides whether the door leaks in February. Interior doors skip the weatherproofing and move straight to trim.
Stage 5: Hardware, trim, and final adjust (2 – 3 hours)
We set the lockset, deadbolt, and any closer or automatic operator, hang the casing, fill nail holes, and adjust the strike plate so the latch clicks without a shove. You walk it with us, open it half a dozen times, and sign off. On exterior doors, we prime and paint the raw edges the same visit, because a painted edge on a wood or fiberglass door is what keeps moisture out of the slab.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the cost swing in a door comes from three decisions: the slab material, whether the frame is replaced or reused, and how much glass and hardware you add.
- Fiberglass exterior doors – the best match for Orinda’s hot summers and fire-hardening requirements. Holds a stain or paint for a decade, resists dents, and can carry a certified fire rating. Pricier than steel by $150 – $400 per door.
- Steel exterior doors – the least expensive way to get a strong, paintable entry. It dents at the kick plate and rusts at any cut edge, so the finish matters more than the slab.
- Solid-core wood interior doors – noticeably quieter, holds a hinge better than hollow-core, and takes a heavier closer. The upgrade is worth it for bedrooms off a hallway; less so for a closet.
- Hollow-core interior doors – the $120 – $250 door. Light, cheap, and fine until a kid slams one and the face delaminates. Most Orinda homeowners use them for closets only.
- Glass and glazing – a half-lite or full-lite entry with tempered or laminated glass is the single biggest jump in cost. Laminated glass is the fire-hardening choice on the exterior.
- Hardware – a basic builder-grade knob is fine. A keyed entry set with a matching deadbolt, or a smart lock, runs $150 – $500 in hardware alone and needs a slightly larger bore.
- Brands – Andersen and Marvin on the exterior premium side; CertainTeed and Owens Corning appear in the wider envelope and roofing scope, not on the doors themselves.
What Door Installation Costs in Orinda, CA
Plan on $650 – $2,400 per opening for a typical interior or standard exterior door installed and trimmed, and $2,800 – $6,500 for a heavy custom or wide exterior unit that needs reframing. A whole-house swap (say eight to ten interior doors plus two entries) usually lands between $6,500 and $14,000.

What pushes a job to the low or high end:
- Opening condition – a straight frame shims in an hour. A racked one from a sloped lot’s foundation movement can double the labor.
- Door size and weight – a 36-inch standard slab is quick; a 48-inch custom wine-room or workshop door is a two-person, half-day job.
- Material grade – fiberglass or solid wood versus steel or hollow-core moves the number by $200 – $700 per door.
- Structural change – widening an opening means a header and a permit. That’s where $2,000 – $4,000 enters.
- Permit scope – a straight swap usually needs none. A new opening in a bearing wall does. We pull the permits and pass the inspection on the ones that require it.
A written estimate from us lists the door unit, hardware, trim, labor, permit (if any), and disposal, with the price fixed and no change orders for the scope we agreed. The one thing that isn’t included is any hidden rot behind the frame, which we can’t see until demo day; if we find it, you get the number before we proceed.
See the difference
Before
After
Before
After
Before
AfterWhat Orinda Homes Specifically Do to This Job
Orinda is a wooded, hillside suburb, and door work here inherits the same constraints as everything else: steep-slope access, protected oak and redwood canopy, and fire-hardening requirements that don’t apply in Lafayette or Walnut Creek on flatter ground. Exterior door replacements often need an ember-resistant threshold and non-combustible trim on the WUI-facing side, and if the door sits inside a tree-protected zone (common on the lots off Miner Road and Moraga Way), we plan the material staging around the canopy before the first tool comes out. Mid-century ranches from the 1950s – 1970s dominate the housing stock, and their door frames have had sixty-odd years of seasonal movement, so we routinely shim a door a quarter-inch off-plumb to sit flush. In winter we see fog-driven moisture rot at the bottom of the frame on the north side of the ridge; a sill pan on every exterior replacement handles it. For anything wider than a single door, the geotechnical reality of a sloped lot can mean a stamped detail on the permit. If the door is part of a broader entry or siding refresh, that wider project scope sits on our Windows & Doors in Orinda page. Homeowners also often pair this with Garage Conversion ADU in Orinda, where a matching man-door keeps the envelope consistent, or with Cabinets & Countertops in Orinda when an interior remodel is running at the same time. We cover all of Orinda and the neighboring towns, so a single trip is a single trip. If you’re planning the whole envelope, start with our Windows & Doors service.
Serving Orinda, CA – Our Local Coverage Area
We serve Orinda and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Orinda

A single interior door takes 2 – 4 hours and a standard exterior door takes a full day; a custom or wide entry with reframing runs two to three days. Most jobs finish before we leave the property, which is why we prefer to schedule door work as its own visit rather than tacking it onto another trade.
A straight like-for-like swap usually doesn’t require one; widening an opening in a bearing wall does. We check the scope against Orinda’s building requirements before we commit to a date, and where a permit is required we pull it and schedule the inspection.
Yes, in the majority of cases – the existing rough opening accommodates the new door with shims and trim. If a door has to grow by more than a couple of inches, that’s when we look at the header, and if the header has to change we tell you before we start.
You’re looking at $650 – $2,400 per opening for standard work and $2,800 – $6,500 for a heavy or wide exterior unit that needs reframing. Call (833) 700-4611 for an exact quote – estimates are free, and we’ll put it in writing.
Every door we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. Our technicians have up to 12 years of experience, they’re background-checked and arrive in uniform, and the same guarantee applies whether we’re hanging one door or ten.
Ready for a Free Door Installation Estimate in Orinda?
Call (833) 700-4611 and a live person picks up, any hour. Tell us the door type, the opening, and roughly when you need it, and we’ll schedule a free on-site estimate with a written, line-item quote. Calls are answered around the clock, and there’s no pressure to book on the spot – you get the number, you decide.
Written by the team at Groundwork Construction Co. of Richmond.












