







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Orinda, CA: Answering the First Question
A chain link fence in Orinda, CA typically runs $3,500 – $9,000 for a residential lot line, installed in two to four working days depending on slope and footage. That covers galvanized or vinyl-coated mesh, posts, top rail, tension bands, and concrete-set footings on most residential runs. Steep hillside lots and tree-protected property lines push the number up; flat rear yards pull it toward the low end. Call (833) 700-4611 for a free on-site estimate, and we’ll walk the line with you before anyone quotes a number.

How We Build a Chain Link Fence in Orinda, Start to Finish

Chain link looks simple. On an Orinda hillside, it rarely is. Here’s the actual sequence.
Stage 1: Site walk and line layout (day 1, about an hour)
We walk the property line with you, confirm where the fence can legally sit, and flag anything the layout has to respect: protected oaks, a slope break, an existing retaining wall, a shared line with a neighbor. You decide the run and the gate locations at this stage, because moving a gate later means re-pouring footings.
Stage 2: Utility locate and permit check (day 1, before digging)
No hole gets dug until 811 utility marking is complete. If your property line sits inside a tree-protection zone or crosses a hillside grade change, we confirm whether the town requires a permit and whether an arborist review is needed before the first post. This step is where a lot of Orinda jobs get their schedule built, not the install itself.
Stage 3: Demo and post setting (day 1 – 2, the long part)
Old fencing and brush come out, then posts go in at 8 to 10 foot spacing, set in concrete and left to cure. On slopes, posts are stepped down the grade rather than driven at an angle, which takes longer but keeps the top rail honest. Corner, gate, and end posts get larger footings and deeper embedment than line posts.
Stage 4: Rails, mesh, and tensioning (day 2 – 3)
Top rail, tension wire at the bottom, and mesh stretched and tied off. A properly tensioned chain link fence doesn’t rattle or sag; if you can push the mesh more than an inch or two between posts, it wasn’t stretched right. We tension at the terminal posts first, then work back.
Stage 5: Gates, walkthrough, and cleanup (day 3 – 4)
Gate frames hang, latches and hinges get adjusted, and we walk the run with you. You’ll get a chance to open every gate, check the tension, and confirm the layout matches what we laid out on day one. Cleanup includes hauling the old fencing off-site unless you ask us to leave it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Most chain link decisions come down to four things. Here’s the honest trade-off on each.
- Mesh gauge (11.5 vs. 9 vs. 6 gauge): 11.5-gauge is the standard residential weight and the least expensive. 9-gauge is noticeably stiffer and resists bending from kids, dogs, and branches; it’s worth it if the fence takes real abuse. 6-gauge is heavy commercial weight and usually overkill for a backyard.
- Coating (galvanized vs. vinyl-coated): Galvanized is the budget choice and holds up fine in dry climates, but it dulls. Vinyl-coated (black or green are the common colors) costs more, looks cleaner against landscaping, and adds a layer of corrosion protection. Black coated chain link reads far less institutional, which matters if the fence is visible from the street.
- Height (4′, 5′, or 6′): 4′ is typical for a garden boundary. 5′ is the common middle ground. 6′ is where you’re addressing privacy or containment, and it costs more per foot because of larger posts and deeper footings.
- Add-ons: Privacy slats (woven into the mesh, 60 – 85% visual block), a top-rail vs. top-tension-wire build, and gate style (walk gate vs. double drive gate) all move the price. Slats are the single biggest add-on and can add a noticeable percentage to the run.
If you’re weighing chain link against something more finished, the neighboring options are already detailed on our Fence Installation in Orinda page. This page stays on chain link on purpose.
What Chain Link Fence Costs in Orinda, CA
Expect $3,500 – $9,000 for a typical residential chain link fence in Orinda, all-in, including materials, footings, and install. Within that range, here’s what moves the number:

- Linear footage: The single biggest driver. A short 60-foot side yard sits near the bottom; a full perimeter around a large lot sits near the top.
- Slope and access: Stepped posts on a hillside take longer than a flat run, and tight access (narrow driveways, no room for a truck at the fence line) adds labor. This is common on Orinda’s hillside lots.
- Existing condition: Removing an old fence, concrete footings, or encroaching brush adds demo time. A clean line installs faster.
- Coating and gauge: Vinyl-coated and heavier-gauge mesh push the job toward the upper end.
- Permit scope: If the run triggers a town permit or tree-protection review, that adds cost and schedule.
A written estimate should itemize footage, gauge, coating, post spacing, gate count, demo, and permit handling. What typically isn’t included unless you ask: arborist reports, retaining wall work, and landscape repair where demo disturbed plantings. We give you a line-item quote up front so the number you see is the number you pay. Groundwork Construction Co. backs every install with our 730-Day Done Right Promise: if it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Orinda Homes Specifically Do to This Job
Orinda is a wooded, hillside suburb, and almost every fence project here runs into the same three realities: steep slope, tree protection, and fire-hardening requirements that don’t apply in flatter neighboring towns like Lafayette or Piedmont. That shapes chain link work in specific ways. A hillside grade change means posts are stepped, not driven straight, and footings go deeper on the downhill side; wind exposure on an exposed ridge can argue for heavier gauge and closer spacing. Mature oak and redwood canopies mean the fence line often needs to route around protected root zones, and it’s not unusual for a project here to begin with an arborist review before the layout is final.
The housing stock leans toward mid-century ranch homes from the 1950s through the 1970s, and many original property-line fences from that era are now failing at the posts, not the mesh. That’s the most common call we get: a rusty post line leaning into a neighbor’s yard, mesh that’s still intact. In the 94563 hillside neighborhoods, we also see chain link used as a temporary or secondary boundary around additions and deck rebuilds, which is where homeowners often pair this work with ADU Site Prep & Utilities in Orinda so the site gets fenced once, cleanly, before trades arrive. We cover the full Orinda area, and our Fence Installation service handles the wider scope if you’re fencing more than one line. If a gate needs to tie into a new structure, we coordinate with Door Installation in Orinda rather than leaving a gap for someone else to solve later.
Serving Orinda, CA – Our Local Coverage Area
We serve Orinda and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Chain Link Fence in Orinda

Most residential chain link fences in Orinda take two to four working days, with hillside lots and heavy demo pushing toward the longer end. Permit review and arborist checks can add calendar time before install begins, so the schedule is usually set at the site walk, not the day we dig.
Permit requirements depend on height, location, and whether the run sits inside a tree-protection or hillside zone. We confirm the requirement for your specific lot during the estimate rather than guessing, and we handle the permit paperwork if one is needed. Call (833) 700-4611 and we’ll tell you what applies to your property.
In most cases, yes. Chain link footings are narrow compared with wood or masonry posts, so the disturbance footprint is smaller and the line can route around protected trees and existing structures. If the run has to cross a root zone or a slope break, we flag it before digging.
Most residential jobs land between $3,500 and $9,000, driven mainly by linear footage, slope, coating type, and demo. Call (833) 700-4611 for an exact quote; estimates are free and itemized.
Every chain link install we do is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That covers workmanship on posts, tensioning, and gates. Material warranties come separately from the manufacturer.
Get a Free Chain Link Fence Estimate in Orinda
Call (833) 700-4611 to schedule a free on-site estimate for a chain link fence in Orinda. We’ll walk the line, check slope and tree zones, confirm whether a permit applies, and give you an itemized written quote with no surprises. Calls are answered by a live person, and estimates are free. Financing at 0% for 18 months is available, plus $1,000 off projects over $10,000.
Written by the team at Groundwork Construction Co.












